Access Point cisco مدل WAP200

Cisco WAP200 Wireless-G Access Point: PoE/RangeBooster

Cisco Small Business Access Points

Wireless Access Point That Extends Network Connectivity for Small Businesses

Highlights

● Increases wireless throughput and range and reduces “dead spots” in the wireless coverage area with

RangeBooster technology

● Connects to Power over Ethernet devices, simplifying installation and eliminating the need for and cost of

installing external power supplies

● Protects network traffic to safeguard business information with enhanced security, including advanced

encryption and security monitoring for additional visibility

● Provides consistent network performance with integrated quality of service to support voice and video

applications

● Simplifies installation and configuration with easy-to-use web interface

Product Overview

RangeBooster technology is a compatible add-on to standard Wireless-G that can nearly double your wireless

network’s range and increase its throughput by up to 35 percent. Unlike ordinary wireless technologies that are

confused by signal reflections, RangeBooster uses two smart receivers at each end to detect and decode reflected

signals at distances where standard technologies give up. You’ll find that “dead spots” in the wireless coverage area

are reduced, too.

The advanced security features make this solution ideal for your business. Advanced wireless security using Wi-Fi

Protected Access (WPA2) with up to 256-bit encryption, and Wireless Security Monitoring give your business the

visibility and protection it needs. Used when Cisco® WUSB 200, WMP200 or WPC200 Wireless adapters are

present, Wireless Security Monitoring alerts you of possible wireless intruders and vulnerabilities in the wireless

deployment and gives you visibility into denial-of-service attacks.

The Cisco WAP200 Wireless-G Access Point (Figure 1) lets you connect Wireless-G (802.11g) or Wireless-B

(802.11b) devices to your wired network so you can add PCs to the network with no cabling hassle. Power over

Ethernet (PoE) support makes it easy to install - you can mount the access point anywhere, even without ready

access to a power plug. With appropriate PoE support at the other end, you need to run only one cable to the access

point to deliver both data and power. Of course, you can also use the included AC adapter if power is available

nearby.

The integrated quality of service (QoS) features provide consistent voice and video quality on both the wired and

wireless networks, enabling the deployment of business-quality voice over IP (VoIP) and video applications.

Additional features like multiple basic service set identifiers (BSSIDs), wireless roaming, and auto-channel selection,

make this solution ideal for your business.

Features

● 10BASE-T/100BASE-TX Ethernet port, autosensing half/full duplex and medium dependent interface (MDI) and

MDI crossover (MDI-X)

● Full backward compatibility with 802.11b

● Easy installation and configuration

● Supports Wired Equivalent Privacy (WEP), WPA Pre-Shared Key (WPA-PSK), WPA2-PSK, WPA-ENT, and

WPA2-ENT authentication (802.11i ready)

● SMA detachable dipole antennae with 1x2 multiple-input, multiple-output (MIMO) to increase coverage

● Supports PoE or external DC power

● Supports 4 BSSID and 802.1Q VLAN to service set identifier (SSID) mapping

● Supports Simple Network Management Protocol (SNMP) and features an intuitive web-based interface

● Wi-Fi Multimedia (WMM) wireless QoS support, upgradable to 802.11e

● Supports wireless roaming based on 802.11F (Inter-Access Point Protocol [IAPP])

● Supports access point, bridge mode, and repeater mode

● Supports wireless security monitoring (working together with Cisco WUSB 200, WMP200 or WPC200

client cards)

● Supports wireless client isolation

● Limited lifetime warranty

Specifications

Table 1 gives specifications, package contents, and minimum requirements for the Cisco WAP200 Wireless-G

Access Point.

Table 1. Specifications for the Cisco WAP200 Wireless-G Access Point: PoE/RangeBooster

Specifications

Standards IEEE 802.11g, IEEE 802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af (PoE), 802.1p (QoS priority), 802.1q (VLAN),

802.1X (security authentication), 802.11i ready (security WPA2), 802.11e ready (wireless QoS), 802.11F (wireless

roaming)

Ports 10BASE-T/100BASE-TX Ethernet, 12V DC power

Buttons Reset

Cabling type Unshielded twisted pair (UTP) Category 5

LEDs Power, PoE, Wireless, Ethernet

Operating system Linux

Setup/Configuration

Web user interface Built-in web user interface for easy browser-based configuration (HTTP/HTTPS)

Management

SNMP version SNMP version 1, 2c, 3

Event logging ● Email notification

● Remote syslog

Web firmware upgrade Firmware upgradable through web browser

Diagnostics Flash, RAM, LAN, WLAN

Dynamic Host Configuration

Protocol (DHCP)

DHCP client

Operating Modes

Access point Access point mode, point-to-point bridge mode, point-to-multipoint bridge mode, repeater mode

Wireless

Spec/modulation Radio and modulation type: 802.11b/DSSS, 802.11g/OFDM

Channels Operating channels: 11 North America, 13 most of Europe (ETSI and Japan)

External antennas 2 (omnidirectional) SMA detachable

Transmit power Transmit power (adjustable) at normal temperature range:

● 802.11b: 18~19 dBm

● 802.11g: 14~15 dBm

Antenna gain in dBi 2

Receiver sensitivity 802.11.g: 54 Mbps at -72 dBm, 802.11.b: 11 Mbps at -85 dBm

Security

WEP/WPA/WPA2 WEP 64-bit/128-bit, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT

Access control Wireless connection control: MAC-based

SSID broadcast SSID broadcast enable/disable

802.1X IEEE 802.1X support

Wireless client isolation Wireless client devices can be isolated from each other either within an SSID or between 2 SSIDs

Wireless Security Monitor Scan and classify wireless devices in the network

Report new client and access point joining network and suspicious network events (works together with Cisco

WUSB 200, WMP200 or WPC200 business client adapters):

● Intrusion alarms (e.g., rogue client detected, spoofed MAC address)

● Denial-of-service alarms (e.g., duration attack, association table full)

● Vulnerability alarms (e.g., access point is not using encryption, access point is broadcasting SSID)

● Other alarms (e.g., low speed connection)

Quality of Service

QoS ● 4 queues

● Wi-Fi Multimedia (WMM) wireless priority

General

● Wireless roaming based on IAPP

● Auto-channel selection

Environmental

Dimensions

W x H x D

6.69 x 8.07 x 7.68 in.

(170 x 205 x 195 mm)

Unit weight 0.88 lb (0.4 kg)

Power 12V 1A DC Input, and IEEE 802.3af compliant PoE

Maximum power draw: 3.36W

Certification FCC, ICES-003, CE

Operating temperature 32º to 104ºF (0º to 40ºC)

Storage temperature -4º to 158ºF (20º to 70ºC)

Operating humidity 10% to 85% noncondensing

Storage humidity 5% to 90% noncondensing

Package Contents

● Cisco WAP200 Wireless-G Access Point

● 2 SMA detachable dipole antennas

● User guide on CD-ROM

● Ethernet network cable

● Power adapter

● Product stands

● Registration card

Minimum Requirements

● 802.11b, 802.11g wireless adapter with TCP/IP installed per PC

● Switch/router with PoE support or PoE injector when used with PoE

● Web-based configuration: Java-enabled web browser

Product Warranty

Limited lifetime hardware warranty with return to factory replacement.